Get in Touch
Blog
  1. Home >
  2. Blog Detail

Aggregate crushing value test lab report

Apr 08, 2021

2500−1990 ACV = 100 2500 = 20.4 % Result: Aggregate crushing value = 20.4% Result Analysis: 1. The value is higher when more percentage of aggregates crush and break into smaller pieces which indicates the aggregates are of a lower quality

Get Price
  • aggregate crushing value test lab report
    aggregate crushing value test lab report

    Aggregate Crushing Value 36.81 40.60 (%) Aggregate Crushing Mean 38.71 value (%) 5.1 Sample calculations 1167.8 Sample1. Aggregate Crushing Value (ACV) = 3172.8 100% = 36.81%. 1261.7 Sample2. Aggregate Crushing Value (ACV) = 3107.4 100% =

  • aggregate crushing value test lab report
    aggregate crushing value test lab report

    adversely affected. The strength of coarse aggregates is assessed by aggregates impact test. The aggregate impact value provides are lative measure of resistance to crushing under a. gradually applied compressive load. T o achieve a high quality of pavement, lower aggregate. impact value should be preferred

  • aggregate crushing value test lab report
    aggregate crushing value test lab report

    Calculation of Aggregate Crushing Value. The crushing value of aggregates is measured in the ratio between the crushed aggregates, obtained from the IS sieve 2.36mm and the weight of the dried aggregate sample. At least three samples should be tested from the same batch and average value to get accurate results. The crushing value of aggregate = (W2/W1) x 100. Lab Report

  • aggregate crushing value test lab report
    aggregate crushing value test lab report

    1.The ratio of the weight of fines formed to the total sample weight in each test shall be expressed as a percentage, the result being recorded to the first decimal place: Aggregate Crushing Value = (B/A) X 100 where A = weight of oven-dried sample B = weight in 'g' of fraction passing through 2.36 mm IS sieve. 6.Video Aggregate Crushing Value Test

  • aggregate crushing value test lab report
    aggregate crushing value test lab report

    Procedure of Aggregate Crushing Value. Take a sample of aggregates by sieving through 12.5mm and retained on 10mm. The aggregate shall be tested in dry surface conditions. If dried by heating, the period of drying shall not exceed 4 hours and temp shall be 100-110 deg C

  • aggregate crushing value test lab report
    aggregate crushing value test lab report

    This test is repeated once or twice and the average crushing value of the aggregate is determined. The average crushing value in the different tests is the actual crushing value of aggregate. Important points to remember. It is recommended that the crushing value of aggregate should be less than 30%

  • aggregate crushing value test lab report
    aggregate crushing value test lab report

    DOC Aggregate crushing value Test Lab Report Adnan. ... METHOD B1 THE DETERMINATION OF THE. The aggregate crushing value ACV of an aggregate is the mass of material expressed as a percentage of the test sample which is crushed finer than a 236 mm sieve when a sample of aggregate passing the 132 mm and retained on the 950 mm sieve is subjected

  • aggregate crushing value test lab report
    aggregate crushing value test lab report

    Mar 30, 2020 Procedure of Aggregate Crushing Value Test:-. Sieve the test material through 12.5 mm and 10.0 mm IS sieve. Take test samples of aggregates passing through 12.5 mm IS sieve and retained on 10 mm IS sieve (minimum 3 Kg). Dry theme in an oven for 4 hours at a temperature of 100 C to 110 C and then cool at room temperature

  • aggregate crushing value test lab report
    aggregate crushing value test lab report

    1.0 AGGREGATE IMPACT VALUE TEST 1 1.0 INTRODUCTION Aggregates used in road construction, should be strong enough to resist crushing under traffic wheel loads if the aggregates are weak, the stability of the pavement structure is likely to be adversely affected

  • aggregate crushing value test lab report
    aggregate crushing value test lab report

    report it to the nearest 0,1% on form B4/3 or a similar form. Aggregate crushing value (wet or dry) percentage (m/m) = ACV B A = x 100 where : A = mass of test sample before test. B = mass of fraction passing the 2,36 mm sieve. 5 NOTES 5.1 The test described above is the standard test but if the available aggregate does not contain

  • aggregate crushing value test lab report
    aggregate crushing value test lab report

    DETERMINATION OF AGGREGATE CRUSHING VALUE 2.1 Object - This method of test covers the procedure for determining aggregate crushing value of coarse aggregate. NOTE 1 -The ‘aggregate crushing value’ gives a relative measure of the resistance of an aggregate to crushing under a gradually applied compressive load. With aggre

  • aggregate crushing value test lab report
    aggregate crushing value test lab report

    Feb 25, 2012 The strength of coarse aggregates is assessed by aggregates crushing test. The crushing value provides a relative measure of resistance to crushing under a gradually applied compressive load. To achieve a high quality of pavement, aggregate possessing low aggregate crushing value should be preferred. 2.0 Objective

  • aggregate crushing value test lab report
    aggregate crushing value test lab report

    Therefore, aggregate used for such propose should have sufficient toughness to resist their disintegration due to the impact. This important property of aggregate is determined by the aggregate impact value test. This resistance of aggregate may differ from resistance to gradual load which we measure in the crushing value test

  • aggregate crushing value test lab report
    aggregate crushing value test lab report

    The aggregate crushing value (ACV) of an aggregate is the mass of material, expressed as a percentage of the test sample which is crushed finer than a 2,36 mm sieve when a sample of aggregate passing the 13,2 mm and retained on the 9,50 mm sieve is subjected to crushing under a gradually applied compressive load of 400 kN 2 APPARATUS 21 An

  • aggregate crushing value test lab report
    aggregate crushing value test lab report

    Aggregate Crushing Value Test – Determine Aggregate Crushing Strength. 7 LAB TESTS ON AGGREGATE TO CHECK QUALITY FOR USE IN Sep 12, 2015 The aggregate crushing value provides a relative measure of resistance to crushing under gradually applied crushing load

  • aggregate crushing value test lab report
    aggregate crushing value test lab report

    The test aims at looking for the forces required to produce 10% of fine values (i.e. weight of fines aggregates/weight of all aggregates = 10%). This test is very similar to Aggregate Crushing Test in which a standard force 400kN is applied and fines material expressed as a percentage of the original mass is the aggregate crushing value

  • aggregate crushing value test lab report
    aggregate crushing value test lab report

    Aggregate Impact Values, (AIV’s), below 10 are regarded as strong, and AIV’s above 35 would normally be regarded as too weak for use in road surfaces. Aggregate Impact Values and Aggregate Crushing Values are often numerically very similar, and indicate similar aggregate strength properties. Aggregate Impact Value; Test Specifications:

Related Product